Enertec AirAudit

AirAudit for compressed air finds out the savings potential and development targets of your compressed air system

Do you know how to improve the performance of your compressed air system, save energy and money, and reduce emissions?

With the measurement, we find out the current state of your compressed air system and make our solution proposals for its development. AirAudit is worth taking, especially if you are planning new investments and development measures. We have found that in many cases no new equipment investment is required to address capacity needs, as the analysis can be used for optimizing the existing system.

We study your system comprehensively – from compressor operation to compressed air quality and energy consumption. You will get measured information about your compressed air system, on the basis of which you can take the right development measures.

We analyze your compressed air system as a whole

Compressed air is a very reliable commodity, that is why attention is often paid to its output only in the event of disturbances. However, your compressed air system is as strong as its weakest links, therefore, it is worth doing a system analysis well in advance.

In a properly functioned compressed air system, all devices work properly both individually and as a whole. We do not only focus on compressors, but on the functionality of your entire compressed air system, the quality of the compressed air produced, and the pressure level and its variations. In addition to compressors, the compressed air system includes a compressed air distribution network and after-treatment equipment such as filters and dryers.

With the help of the AirAudit, you can find out for example:

Why are your devices not working optimally or due to their faults?
Is your compressed air system wasting energy and where could it be saved?
What is the efficiency of the compressors?
Is there room for improvement in the quality of your compressed air?
Do you need more compressor capacity and how should you select the size? You will receive an assessment of the adequacy of the current compressor capacity from us, as well as any suggestions for improvements to the operation of the compressors.
Whether your capacity needs are still due to the efficiency of the compressors – or if the problem is too little tank capacity, an undersized dryer or something else to fix.
Pressure level and its variations. If, for example, the pressure in the compressed air piping varies and the compressed air is not always sufficient, we will use the compressed air to find out the cause of the problems.

What is measured in AirAudit?

We collect key data from your compressed air system every second, usually for seven days.

Measurements do not cause production interruptions. In fact, we hope your production is running normally during the measurement.

Measurable data:

Power consumption of each compressor (total power)
Output pressure after compressors
Air pressure after air-treatment
Mains pressure from several points
Temperature of the compressed air going to the dryers
Compressor room temperature
Compressed air dew point

Developing energy efficiency is an important part of compressed air. We will find out how much energy your compressed air system consumes and what is the efficiency of the compressors. You will also find out how much pressure loss is caused by after-treatment and the compressed air network, pressure fluctuations and an estimate of the adequacy of the receiver capacity.

The report shows how well the compressor running settings match your compressed air consumption. Compressor pressure settings may be unnecessarily high. In this case, the compressors run in vain and energy is wasted. In addition, compressors require more frequent maintenance and wear faster.

More than 800 AirAudit for compressed air has implemented

We have helped hundreds of companies and organizations to make more efficient use of the compressed air system both in Finland and abroad.

Measured data

There is no need to guess the status of your compressed air system, as you will receive a comprehensive report of the measurements, which we will personally review with you.

Energy efficiency

AirAudit reveals the energy saving potential of your system. You will receive a comprehensive energy analysis and suggestions on how you can reduce your energy consumption.

Development proposals

AirAudit serves as a starting point for optimizing your compressed air system. You will receive development suggestions from us, which you can take to improve the efficiency and cost and energy savings of your compressed air system.

No production interruptions

You can keep your production running as normal during the measurement. Wireless and battery-powered Sarlin Data Loggers collect data securely from even a large factory.

Turkish compressed air

Enertec's compressed air services are distinguished by quality work and thorough analysis of customer's demand in compressed air

This is how your compressed air system is arranged for AirAudit

Contact us and agree on a suitable time for the analysis of your compressed air system.
We install Enertec’s Dataloggers that collect data on your compressed air system and compressed air applications. You can continue your production as usual.
The devices measure your compressed air system for 1 to 7 days. We will restore back the equipment when the measurement is complete.
We analyze the measured data and review the results
With you in person. You will receive a comprehensive report of the findings.
With our solution proposal, you get comprehensive development proposals on how to improve the energy efficiency and reliability of your compressed air system.